Thursday, December 26, 2024
FGF
FGF
FGF

Öhlins Prototype Digital XC Suspension Raced on the MTB World Cup: Uncovered!

Final 12 months we noticed Öhlins debut all-new XC suspension on the races, and this 12 months they’re again with new electronically-controlled prototypes. The idea seems to be the identical carbon-crown RXC34 fork and TXC2 Air shock, however now mechanical lockouts are changed with digital controls. Within the pits, Titouan Carod’s BMC mechanics largely saved all the pieces neatly wrapped up. However out on the observe we acquired a more in-depth take a look at what appears to be like just like the sensible controller added onto the rear shock…

Öhlins prototype digital XC MTB suspension

Öhlins prototype electronic XC mountain bike suspension raced at Nove Mesto MTB World Cup, Titouan Carod warming up on BMC Fourstroke
(All pictures/Cory Benson)

Recognizing Carod warming up for the Nové Město na Moravě brief observe over the weekend, we seen and additional field protruding of the entrance of his Öhlins TXC Air rear shock, tucked in between the entrance shock mount on his BMC Fourstroke XC race bike. It seems that what we noticed appears to be a prototype electronically-controlled cross-country air shock and fork from the Swedish suspension specialists.

Öhlins prototype electronic XC mountain bike suspension raced at Nove Mesto MTB World Cup, racing uncovered

It’s not fairly the primary time we’ve seen prototype digital suspension from Öhlins. We’ve seen a number of variants of Loic Bruni racing digital Öhlins DH prototypes, each on a reconfigured Specialised Demo and an all-new prototype bike that’s nonetheless in growth.

However whereas all that prototype DH tech was well-covered below huge cowls, this BMC is fitted with a lot smaller tech that extra simply tucked into the in any other case inventory body.

Plus, it’s being left uncovered, at the very least for racing…

Prototype digital TXC Air shock wrapped up tight within the pits, largely

Öhlins prototype electronic XC mountain bike suspension raced at Nove Mesto MTB World Cup, all wrapped up TXC2Air shock

For essentially the most half, the Group BMC Racing mechanics tried to maintain the brand new Öhlins digital prototypes on Carod’s bike wrapped up inside a velcro-on neoprene sleeve. Not less than after they weren’t engaged on the bike.

However the weekend’s cross-country racing began off fairly moist & muddy, so there have been loads of instances after they pulled again the covers to service the bike.

So, why would possibly they maintain the prototypes uncovered out on the observe and for racing, but wrap it up within the pits?

Öhlins prototype electronic XC mountain bike suspension raced at Nove Mesto MTB World Cup, uncovered in the pits

My guesses could be 1 or 3 potentialities. Both the electronics want airflow to get one of the best operate, or the quilt would possibly merely impede some motion? The rider or mechanics might have quick access on the observe to make changes, in any other case inaccessible below the neoprene cowl? Or maybe, they only must see the way it stands as much as the weather in a real-world racing state of affairs.

In any case, the result’s that we acquired a fairly good sneak peek by preserving our eyes open.

Digital prototype Öhlins RXC34 Carbon Air fork

Öhlins prototype electronic XC mountain bike suspension raced at Nove Mesto MTB World Cup, a RXC34 mk.1 fork with custom internals

OK, so we all know there’s some digital management. However what suspension are we working with?

It seems that solely Titouan Carod is racing on the prototype digital suspension. The remainder of the BMC workforce will get mechanical remotes. And it appears to be like like he’s working with the Öhlins RXC34 fork that we detailed final summer time, based mostly on these lowers. After all, we in all probability wouldn’t name it an m.1 fork anymore, as clearly he’s acquired some customized next-gen tech inside. And his identify on the fork legs.

Öhlins prototype electronic XC mountain bike suspension raced at Nove Mesto MTB World Cup, everything hidden inside the RXC34 fork

What digital controls that exist are completely within the left leg. That’s the place the 3-position (Open, Pedal, Lock) OTX14 compression damper cartridge is on the usual Öhlins RXC34 fork. (The quantity-adjustable air spring is in the fitting leg.)

We don’t see an apparent exterior adjustment right here. However that small gold screw is similar as discovered on the entrance of the shock management/battery field. So it’d provide some adjustability extra than simply holding the cap on.

A single wire (& inline connector) exits, and heads into the body subsequent to the mechanical dropper distant cable. Presumably, the fork then connects with the system mind, on the rear shock.

Tidy Digital Distant Management

Öhlins prototype electronic XC mountain bike suspension raced at Nove Mesto MTB World Cup, tiny twist switch remote control

For rider mode management of the prototype digital suspension, Öhlins offers Carod a tidy little thumb-actuated twist shifter/swap. Wired into the system via the Fourstroke’s inside body routing, the controller doesn’t take up a lot house in between the brake lever and grip. (Its wire enters the alternative of the headtube along with the rear brake.)

Öhlins prototype electronic XC mountain bike suspension raced at Nove Mesto MTB World Cup, Is that a Zirbel controller?

That mode shifter appears to be like loads like a Zirbel Ring Swap with their WE03 Ring for the thumb button. I’m probably not positive, since Zirbel’s normal Ring Swap sometimes has 2 wires popping out of it. However maybe Öhlins simply labored along with Zirbel to create the distant they wanted for his or her prototype suspension controls.

Uncovered and Up Shut!

Öhlins prototype electronic XC mountain bike suspension raced at Nove Mesto MTB World Cup, unwrapped

Now for the correct spy photographs!

Group BMC mechanics have been as cautious as they could possibly be to maintain their Öhlins prototype digital XC suspension out of direct sight within the pits.

However as soon as racing was underway, the mechanics unwrapped the shock.

But, what they saved lined doesn’t actually reveal an excessive amount of in any case.

Öhlins prototype electronic XC mountain bike suspension raced at Nove Mesto MTB World Cup, uncovered in the pits, and up close

All we will actually see is a slim field extending ahead from the damping controls of the TXC Air shock. The truth is, a more in-depth take a look at the photograph we snuck from the workstand (above) suggests the shock itself is wholly unchanged. There’s only a small digital actuator bolted on prime, as an alternative of the mechanical distant actuator, which in fact is sensible for simplicity’s sake.

Öhlins prototype electronic XC mountain bike suspension raced at Nove Mesto MTB World Cup, unwrapped and up close

Then what you get is that this field is simply the battery and mind of the system. We see the 2 wires coming in from the fork & distant swap to connect with the field simply in entrance of the higher shock eyelet. And the wire for the rear shock energy & management exits out of the center of the field on the left/non-driveside.

OK, so now we wait.

Neither Öhlins nor BMC have formally commented on what we see right here. And it’s solely being race-tested on one rider’s bike. So don’t anticipate it too quickly. With that stated although, it was lower than half a 12 months between after we first noticed Öhlins XC suspension prototypes till the time you could possibly truly purchase them. So perhaps we gained’t have so lengthy to attend!

Ohlins.com/MountainBike

Related Articles

LEAVE A REPLY

Please enter your comment!
Please enter your name here

Latest Articles